adjustablebedparts.com
  • Home
  • ADJUSTABLE BED PARTS INDEX
  • IN HOME SERVICE
  • ABOUT US
  • Testimonials
  • Contact Us
  • RETURN POLICY
  • USB PORTS
760.773.2337

Copyright 2011-2026 All rights reserved. No parts of this site may be used or copied without prior consent.

HOME / ABOUT US / PARTS / CONTROL UNITS / SERVICE / RETURN POLICY
OKIN CONTROL UNITS
CU358-2-L FOR WIRELESS REMOTE
image
This is one of the common control units used on beds without massage. It only operates head and foot lift motors. There are several variations of this control unit with the same model number but different part numbers (JLDP #). They are all interchangeable. This unit has one multi-function port to support various features such as a sync cable and a power-down box. Generally only the emergency poser down box is the only thing attached to this control unit unless you are using a single king mattress over two separate bases. In that case, you must use the x-sync cable. On newer bases, this has been replaced by the Keeson MC120/CU380 control unit. There is also a wired version of this control unit. This control unit uses the Ergo Essentials input cord and a 29-volt/1.8 or 2 amp power supply. Most Okin non-massage hand wands can be used with this control unit. The process to sync a hand control to this unit depends on the hand control used. 1. If there is no emergency power down box attached, using a paper clip or other narrow object, push the recessed “reset” button on the side of the box twice fast. This will cause the LED on the side of the box to light up. If you have the power-down box attached, press the round black button on top of the power-down box twice, causing the white LED light beside it to illuminate. 2. If there is a small button inside the battery compartment on the hand control, immediately press and hold the button. It will blink several times, and then both the light on the hand control and the light on the control box will turn off. 3. If there isn’t a button inside the battery compartment then press the head up button and the foot down button at the same time and hold until the light on the control box turns off.
image
image
image
image
image
image
LIFT MOTOR PORTS
SAMPLELABEL
MULTIFUNCTION, POWER, ANDPROGRAMMING PORTS
HERE ARE JUST THREE EXAMPLES OF HAND CONTROLS THAT WILL WORK ON THIS CONTROL UNIT
___________________________________________________________________________________
CU358-2
STARTING AT $175
This is a common Okin control unit used on beds with dual massage. It operates a head and foot lift motor and supports 2-4 massage motors. There are several variations of this control unit with the same model number but different part numbers (JLDP #). They are all interchangeable. This unit has one multi function port to support various features such as a sync cable, power down box, under bed lighting and USB ports. To connect more than one feature you must use various 2 or 3 lead splitters, depending on how many options you add. This control unit uses the Ergo Essentials input cord and a 29 volt/2 amp power supply. Most all Okin dual massage hand wands can be used with this control unit. There are two ways to sync the hand control to this unit. 1. If there is no emergency power down box attached, using a paper clip or other narrow object, push the recessed “reset” button on the side of the box twice fast. This will cause the LED on the side of the box to light up. If you have the power-down box attached, press the round black button on top of the power-down box twice, causing the white LED light beside it to illuminate. 2. If there is a small button inside the battery compartment on the hand control, immediately press and hold the button. It will blink several times, and then both the light on the hand control and the light on the control box will turn off. 3. If there isn’t a button inside the battery compartment then press the head up button and the foot down button at the same time and hold until the light on the control box turns off.
image
image
image
image
image
image
image
HERE ARE JUST THREE EXAMPLES OF HAND CONTROLS THAT WILL WORK ON THIS CONTROL UNIT
MULTIFUNCTION PORT
SAMPLE LABEL
POWER PORT
STARTING AT $175
_______________________________________________________________________________________
CU358-4
image
image
This is the Okin control unit used on beds with either a head tilt motor or a lumbar lift motor, in addition to the head and foot lift motor and massage motors. You can tell the difference by looking at which motor port is open - lift or tilt. They have different part numbers (JLDP #) and use a different hand control. This unit has one multi-function port to support various features such as a sync cable, power down box, under bed lighting and USB ports. To connect more than one feature you must use various 2 or 3 lead splitters, depending on how many options you add. This control unit uses the Ergo Essentials input cord and a 29 volt/2 amp power supply. There are two ways to sync the hand control to this unit
1. If there is no emergency power down box attached, using a paper clip or other narrow object, push the recessed “reset” button on the side of the box twice fast. This will cause the LED on the side of the box to light up. If you have the power-down box attached, press the round black button on top of the power-down box twice, causing the white LED light beside it to illuminate. 2. If there is a small button inside the battery compartment on the hand control, immediately press and hold the button. It will blink several times, and then both the light on the hand control and the light on the control box will turn off. 3. If there isn’t a button inside the battery compartment then press the head up button and the foot down button at the same time and hold until the light on the control box turns off.
image
image
image
image
image
MULTIFUNCTION, POWER, AND PROGRAMMING PORTS
SAMPLE LABEL
EXAMPLES OF HAND CONTROLS WITH HEAD TILT FUNCTION
EXAMPLE OF HAND CONTROLS WITH LUMBAR LIFT FUNCTION
CU358-2-L FOR WIRED REMOTE
_________________________________________________________________________________________
image
image
This control unit used on beds with no massage and a hard wired hand wand. It operates a head and foot lift motor and does not support massage motors. This unit has does not have a multi function port. It attaches directly to one of the lift motors. This control unit uses the Ergo heavy duty input cord and a 29 volt/1.8 or 2.0 amp power supply.
$300
image
image
image
LIFT MOTOR PORTS
POWER AND HAND CONTROL PORTS
POWER CORD
MATCHING HAND CONTROL
DISCONTINUEDLAST ONE!I AM SELLING THIS CONTROL UNIT AND HAND CONTROL AS A SET ONLY$200 SET
_________________________________________________________________________________________
OKIN JLDP-03 CONTROL UNIT
image
image
image
image
This control unit differs from other Okin control units in that the motor ports are round with 8 pins instead of flat with 2 pins. The massage motor ports are also different. Plus. you can plug in up to 4 massage units. It works with the SS-AB1 hand control only. $150
CONTROL UNIT MASSAGE PORTS
SS-AB1HAND CONTROL
LABEL
LIFT MOTOR AND ACCESSORY PORTS

We use cookies to enable essential functionality on our website and analyze website traffic. For more information, read our Cookies and Privacy Policy.

Your Cookie Settings

We use cookies to enable essential functionality on our website and analyze website traffic. For more information, read our Cookies and Privacy Policy.

Cookie Categories
Essential

These cookies are strictly necessary to provide you with services available through our websites.

Analytics

These cookies collect information that is used in aggregate and in an anonymized form to help us understand how our website is being used and how effectively our site is performing.