Copyright 2011-2026 All rights reserved. No parts of this site may be used or copied without prior consent.
Okin Antenna/Power Down boxes have three functions. First, they receive the signal from your hand control. Second, a push button on the side of the box is used to program the hand control to the box. Third, they allow you to flatten the bed in the event of a power outage or if your hand control is lost or damaged.
The boxes have a compartment for two nine-volt batteries, but these are not needed for everyday operation. It is not recommended to install the batteries until you need to lower the bed due to a power outage. Because the emergency power down feature is rarely used, bed owners often forget about it for years. By the time they need to use it, the batteries may have leaked and corroded the box, rendering it inoperable. The batteries also need to be removed from the box for effective troubleshooting. This backup system is designed solely for lowering the bed to a flat position and is not intended for normal up and down operation of the bed.
OKIMAT ANTENNA/POWER DOWN BOXES
TROUBLESHOOTING YOUR OKIMAT ANTENNA/POWER DOWN BOXE
- If your cord to the Lifestyle antenna/power down box is damaged, it may not be the only issue. If the bed was plugged in when the cord was damaged, the circuit board in the motor might also be damaged. Here are are directions to troubleshoot this: 1. Remove Batteries: First, remove the two 9-volt batteries from the power down box. These batteries are only for powering the bed down during a power outage and are not used in daily operation. Leaving them in can provide a false reading. 2. Test Power to the Box: Push the button on the power down box. It should light up red. *If it does not light up, it's not receiving power from the motor. Ensure the motor is powered from the wall outlet by testing the outlet with another device. *If the outlet has power and the box still won't light up, either the power down box or the motor is likely bad. Without a second bed to test the power down box on,
- it's difficult to determine which is faulty.
- 3. Test Hand Control: Push any button on your hand control. *The LED at the top of the hand control should light up and flicker rapidly. *The small LED on the power down box should also flicker green, regardless of whether the bed moves. *f you have multiple beds, all power down boxes will light up, but only the bed programmed to the specific hand wand will move. *If the hand control LED does not light up, but the power down box LED does: The hand control is likely functional, and the LED is simply burnt out. *If neither the hand wand LED nor the power down box LED lights up: Replace the batteries in the hand wand. If the hand wand now lights up, proceed to step 4.
- If it still does not light up, the hand wand is bad.
- 4. Test Power Down Box with Another Bed (If Available): If you have a second bed, swap its power down box with the one on the first bed. The hand control memory is
- stored in the motor. If the second bed's power down box is good and the first bed's motor is good, the bed should operate. If the first bed now works, the original
- power down box was faulty and needs replacement. If the bed still doesn't operate, proceed to step 5. 5. Reprogramming the Bed: *Momentarily push and release the red button on the side of the power down box. *Within 10 seconds, push and hold two programing specific buttons on the hand wand simultaneously. *Both the hand wand LED and the power down box LED should blink slowly twice, then flicker rapidly. *Count to eight and release the buttons. The bed should now be programmed. *If this process is attempted twice without success, the circuit board in the motor is likely bad and requires replacement of the entire motor. Replacement Motor Options: My supplier has discontinued the Oki motors in the Raven frequency previously used for 15-20 years. For a while they used a Raven to Okin upgrade but that has now been discontinued also. They now offer a Raven to Richmat Upgrade Motor Kit: It is a different frequency than the first two kits. This upgrade kit includes a new Oki motor, matching hand control, underfed LED, and a power supply. Your massage motors will plug directly into this motor so no jumpers are needed. This complete kit costs $400, only a little more than the original motor alone. This is a superior option as it includes a new hand wand, essentially making your bed like new, and is the only choice if you wish to use your massage motors. The only drawback is that on some beds, the foot massage motor is mounted in the way and you either have to remove that motor or modify the housing around the motor.
- If you do not wish to use your massage motors at all, I offer an alternative: Used Richmat motor with wired hand wand: $225 (I only have a few)
- Please call me to discuss or place an order.
HOME / ABOUT US / PARTS / SERVICE / RETURN POLICY
RAVEN TO RICHMAT UPGRADE KIT