adjustablebedparts.com
  • Home
  • ADJUSTABLE BED PARTS INDEX
  • IN HOME SERVICE
  • ABOUT US
  • Testimonials
  • Contact Us
  • RETURN POLICY
  • USB PORTS
760.773.2337

Copyright 2011-2026 All rights reserved. No parts of this site may be used or copied without prior consent.

MASSAGE MOTOR ACCESSORIES
RETURN TO MASSAGE MOTORS PAGE
image
MAXWELL 110 VOLT MASSAGE MOTOR MOUNTS
These rubber bushings were used under the 110 volt massage motors on older Maxwell bases. They prevented the massage motors from rattling against the wood platform they are mounted to. They are sold in sets of four.
$ 20
MASSAGE MOTOR MOUNTING KITS
__________________________________________________________________________________
L & P MASSAGE MOTOR MOUNTING KIT
image
image
Some massage motors are suspended in the deck and held in place by a rubber support pad and bracket. This kit consist of the plastic frame, rubber support pad, foam cushioning, anti vibration strips and replacement screws. It is sold as a set only. This kit is for one motor.The picture on the right is a damaged kit on a bed.
$ 80
9432
OKIN MASSAGE MOTOR MOUNTING KIT
image
Some massage motors are suspended in the deck and held in place by a rubber support pad and bracket. This kit consist of the plastic frame, massage motor base, rubber suspension pad, and fibre cushioning. This kit is for one motor. You can buy the individual pieces or the whole kit.
$60 complete kit $25 plastic frame$25 fibre pad $25 massage motor base $25 rubber suspension pad
HHC/MOTOSLEEP MASSAGE MOTOR MOUNTING KIT
Some massage motors are suspended in the deck and held in place by a rubber support pad and bracket. This kit consist of the plastic frame, rubber suspension pad, and foam cushioning. It is sold only as a kit. Each kit is for one motor.
image
$ 60
L&P/RICHMAT MASSAGE MOTOR MOUNTING KIT
image
image
image
This mounting kit uses a cloth blanket to hold the massage motor instead of a rubber pad. It is sold as a kit only. Each kit is for one motor. Motor not included.
$ 90
MASSAGE REPAIR AND EXTENSION CORDS
OKIN LIFT MOTOR AND MASSAGE MOTOR EXTENSION/REPAIR CORD
MASSAGE MOTOR SPLITTERS
On massage motor splitters, one end of the splitter is a plug and the other end has 2 receptacles for the massage motors. Splitters are needed in these three situations -1. Type one splitters - Some one piece queen and king beds had 4 massage motors but only 2 massages motor ports. The splitter allows two massage motors from the same end of the bed to be plugged into one massage motor port on the control unit. You need two splitters, one for each end of the bed.2. Type two splitters - Some control units and some dual actuator lift motors have only one massage port to run both the head and foot massage motors. The Richmat HJC9G control boxes have this feature. Also, on the first Raven to Okin dual actuator motor upgrade kits there was only one massage motor port. The splitter allows both the head and foot massage motors to operate out of that port.
__________________________________________________________________________________
TYPE ONE SPLITTERS
image
image
image
image
OKIN MASSAGE MOTOR SPLITTER
MOTOSLEEP MASSAGE MOTOR SPLITTER
$ 24
$ 35
________________________________________________________________________________________
TYPE TWO SPLITTERS
image
image
image
image
RICHMAT MASSAGE MOTOR SPLITTER
OKIMAT DUAL ACTUATOR MASSAGE MOTOR SPLITTER
$ 35
$ 60
image
image
image
This is a new cord with a male plug on one end and a female plug on the other end. It is approximatly 90" long. It can be used to extend the cord for either motor or you can cut an end off the repair a damaged cord.
The cords for both the lift motors and the massage motors have the same plug on the end. It can be used to repair either part. The original cords are soldered to the motor inside the housing. You could desolder your old one and solder this one back or just cut and splice this to your old cord outside the housing. I cut these plugs from damaged motors. There is no damage on the cords themselves. They just save you money compared to the motor extension cord above.
image
These cords are soldered to a circuit board inside the motor housing. You could desolder your old one and solder this one back or just cut and splice this to your old cord outside the housing. I recommend doing the cutting and splicing. Though the head massage motor has a blue plug and the foot motor has a yellow plug, they are the same. The color is just to aid you in plugging them into the correct plug on the control box
$ 45
$ 25
$ 25

We use cookies to enable essential functionality on our website and analyze website traffic. For more information, read our Cookies and Privacy Policy.

Your Cookie Settings

We use cookies to enable essential functionality on our website and analyze website traffic. For more information, read our Cookies and Privacy Policy.

Cookie Categories
Essential

These cookies are strictly necessary to provide you with services available through our websites.

Analytics

These cookies collect information that is used in aggregate and in an anonymized form to help us understand how our website is being used and how effectively our site is performing.